지원사업
학술연구/단체지원/교육 등 연구자 활동을 지속하도록 DBpia가 지원하고 있어요.
커뮤니티
연구자들이 자신의 연구와 전문성을 널리 알리고, 새로운 협력의 기회를 만들 수 있는 네트워킹 공간이에요.
논문 기본 정보
- 자료유형
- 학술저널
- 저자정보
- 저널정보
- 국제구조공학회 Steel and Composite Structures, An International Journal Steel and Composite Structures, An International Journal Vol.42 No.1
- 발행연도
- 2022.1
- 수록면
- 1 - 22 (22page)
이용수
초록· 키워드
오류제보하기
In cold-formed steel (CFS) structures, such as trusses, transmission towers and portal frames, the use of back-to back built-up CFS unequal angle sections are becoming increasingly popular. In such an arrangement, intermediate welds or screw fasteners are required at discrete points along the length, preventing the angle sections from buckling independently.
Limited research is available in the literature on axial strength of back-to-back built-up CFS unequal angle sections. The issue is addressed herein. This paper presents an experimental investigation reported by the authors on back-to-back built-up CFS unequal angle sections with intermediate stiffeners under axial compression. The load-axial shortening behaviour along with the deformed shapes at failure are reported. A nonlinear finite element (FE) model was then developed, which includes material non-linearity, geometric imperfections and modelling of intermediate fasteners. The FE model was validated against the experimental test results, which showed good agreement, both in terms of failure loads and deformed shapes at failure. The validated finite element model was then used for the purpose of a parametric study comprising 96 models to investigate the effect of longer to shorter leg ratios, stiffener provided in the longer leg, thicknesses and lengths on axial strength of back-to back built-up CFS unequal angle sections. Four different thicknesses and seven different lengths (stub to slender columns) with three overall widths to the overall depth (B/D) ratios were investigated in the parametric study. Axial strengths obtained from the experimental tests and FE analyses were used to assess the performance of the current design guidelines as per the Direct Strength Method (DSM); obtained comparisons show that the current DSM is conservative by only 7% and 5% on average, while predicting the axial strengths of back-to-back built-up CFS unequal angle sections with and without the stiffener, respectively.
목차
등록된 정보가 없습니다.
참고문헌 (0)
참고문헌 신청함께 읽어보면 좋을 논문
논문 유사도에 따라 DBpia 가 추천하는 논문입니다. 함께 보면 좋을 연관 논문을 확인해보세요!
-
Stiffening evaluation of flat elements towards stiffened elements under axial compression
Advances in computational design
2018 .01
-
Effect of angle stiffeners on the flexural strength and stiffness of cold-formed steel beams
Steel and Composite Structures, An International Journal
2019 .01
-
Experimental and numerical study of an innovative 4-channels cold-formed steel built-up column under axial compression
Steel and Composite Structures, An International Journal
2022 .02
-
Structural performance of cold-formed steel composite beams
Steel and Composite Structures, An International Journal
2018 .01
-
Effect of stiffened element and edge stiffener in strength and behaviour of cold formed steel built-up beams
Advances in computational design
2016 .01
-
Nonlinear behavior of axially loaded back-to-back built-up cold-formed steel un-lipped channel sections
Steel and Composite Structures, An International Journal
2018 .01
-
Efficient cross-sectional profiling of built up CFS beams for improved flexural performance
Steel and Composite Structures, An International Journal
2020 .01
-
Flexural Strength of cold-formed steel built-up composite beams with rectangular compression flanges
Steel and Composite Structures, An International Journal
2020 .01
-
Experimental capacity of perforated cold-formed steel open sections under compression and bending
Steel and Composite Structures, An International Journal
2017 .01
-
Parametric study and Improved design guidelines of CFS battened built-up columns
Steel and Composite Structures, An International Journal
2021 .09
-
Shear behaviour of thin-walled composite cold-formed steel/PE-ECC beams
Steel and Composite Structures, An International Journal
2023 .01
-
Direct strength method for high strength steel welded section columns
Steel and Composite Structures, An International Journal
2018 .01
-
The effects of stiffener configuration on stiffened T-stubs
Steel and Composite Structures, An International Journal
2022 .08
-
SECTION_SECTION
월간 데코 DECO
2023 .09
-
Behavior of CFS built-up battened columns: Parametric study and design recommendations
Structural Engineering and Mechanics, An Int＇l Journal
2020 .01
-
Experimental study on axial compressive behavior of welded built-up CFT stub columns made by cold-formed sections with different welding lines
Steel and Composite Structures, An International Journal
2020 .01
-
Structural efficiency of various strengthening schemes for cold-formed steel beams: Effect of global imperfections
Steel and Composite Structures, An International Journal
2019 .01
-
Flexural performance of cold-formed square CFST beams strengthened with internal stiffeners
Steel and Composite Structures, An International Journal
2020 .01
-
고열전도 CF/Al 복합재료의 개발을 위한 일방향 CF 프리폼의 제조
대한기계학회 춘추학술대회
2016 .04
-
Experimental and analytical behavior of stiffened angle joints
Steel and Composite Structures, An International Journal
2018 .01
이 논문의 저자 정보
최근 본 자료
댓글(0)
0