지원사업
학술연구/단체지원/교육 등 연구자 활동을 지속하도록 DBpia가 지원하고 있어요.
커뮤니티
연구자들이 자신의 연구와 전문성을 널리 알리고, 새로운 협력의 기회를 만들 수 있는 네트워킹 공간이에요.
논문 기본 정보
- 자료유형
- 학술저널
- 저자정보
- 저널정보
- 국제구조공학회 Steel and Composite Structures, An International Journal Steel and Composite Structures, An International Journal Vol.18 No.6
- 발행연도
- 2015.1
- 수록면
- 1,331 - 1,351 (21page)
이용수
초록· 키워드
오류제보하기
Cold-formed built-up members are compression members that are common in multiple areas of steel construction, which include cold-formed steel joints and stud walls. These members are vulnerable to unique buckling behaviors; however, limited experimental research has been done in this area. Give this gap, experimental testing of 71 built-up members was conducted in this study. The variations of the test specimens include multiple lengths, intermediate welds, orientations, and thicknesses. The experimental testing was devised to observe the different buckling modes of the built-up C-channels and the effects of the geometrical properties; to check for applicability of multiple intermediate welding patterns; and to evaluate both the 2001 and 2007 editions of the American Iron and Steel Institute (AISI) Specification for built-up members in pure compression. The AISI-2001 and AISI-2007 were found to give inconsistent results that at times were un-conservative or overly conservative in terms of axial strength. It was also found that orientation of the member has an important impact on the maximum failure load on the member.
목차
등록된 정보가 없습니다.
참고문헌 (13)
참고문헌 신청
M. Anbarasu / 2013 / Study on the effect of ties in the intermediate length Cold Formed Steel (CFS) columns / Structural Engineering and Mechanics, An Int＇l Journal 46(3):323~335
American Iron and Steel Institute / 2001 / North American Specification for the Design of Cold-Formed Steel Structural Members
American Iron and Steel Institute / 2001 / Commentary on North American Specification for the Design of Cold-Formed Steel Structural Members
American Iron and Steel Institute / 2007 / North American Specification for the Design of Cold-Formed Steel Structural Members
Brueggen, B. / 2005 / Capacity of built-up cold-formed steel axial compression members / Proceedings of the Structural Stability Research Council Conference
American Iron and Steel Institute / 2001 / North American Specification for the Design of Cold-Formed Steel Structural Members
American Iron and Steel Institute / 2001 / Commentary on North American Specification for the Design of Cold-Formed Steel Structural Members
American Iron and Steel Institute / 2007 / North American Specification for the Design of Cold-Formed Steel Structural Members
Brueggen, B. / 2005 / Capacity of built-up cold-formed steel axial compression members / Proceedings of the Structural Stability Research Council Conference
함께 읽어보면 좋을 논문
논문 유사도에 따라 DBpia 가 추천하는 논문입니다. 함께 보면 좋을 연관 논문을 확인해보세요!
-
Finite element modelling of back-to-back built-up cold-formed stainless-steel lipped channels under axial compression
Steel and Composite Structures, An International Journal
2019 .01
-
Nonlinear behavior of axially loaded back-to-back built-up cold-formed steel un-lipped channel sections
Steel and Composite Structures, An International Journal
2018 .01
-
Compressive behavior of built-up open–section columns consisting of four cold-formed steel channels
Steel and Composite Structures, An International Journal
2022 .12
-
Axial capacity of back-to-back built-up cold-formed stainless steel unlipped channels-Numerical investigation and parametric study
Steel and Composite Structures, An International Journal
2021 .09
-
잔류응력 완화 열처리 적용에 따른 AISI A387, 1536V 소재에 대한 효과
한국기계가공학회 춘추계학술대회 논문집
2019 .10
-
Steel 소재별 파편 성능에 대한 실험적 고찰
한국소성가공학회 학술대회 논문집
2022 .05
-
Influence of Strain Induced Martensite Formation of Austenitic Stainless Steel on Wear Properties
Metals and Materials International
2019 .01
-
AISI S100-16(미국) 및 EN 1993-1-3(유럽) 냉간성형강 설계기준 분석
한국강구조학회 학술대회 발표집
2023 .06
-
고온의 대기 및 SO₂ 가스환경 하에서 AISI 304강의 산화 및 부식 특성
Journal of Advanced Marine Engineering and Technology (JAMET)
2018 .09
-
AISI H13 및 M4 혼합분말 적층 시 고온 경도 특성 평가
한국정밀공학회 학술발표대회 논문집
2022 .05
-
예민화된 AISI 304 및 AISI 316 오스테나트강의 부식 특성
한국기계가공학회 춘추계학술대회 논문집
2018 .04
-
AISI 304 스테인리스 강의 전기화학 부식특성에 대한 장시간 열화의 영향
한국기계가공학회 춘추계학술대회 논문집
2019 .04
-
AISI4340강의고온변형거동예측
한국소성가공학회 학술대회 논문집
2019 .10
-
AISI H13 및 M4 혼합분말 적층 시 고온 충격 특성 평가
한국기계가공학회 춘추계학술대회 논문집
2022 .04
-
중심압축력을 받는 냉간성형 탄소강 각형강관 압축재의 좌굴거동에 관한 실험적 연구
대한건축학회논문집
2022 .10
-
AISI D2 공구강의 적층 제조를 위한 금속 바인더 젯팅 공정 연구
한국정밀공학회 학술발표대회 논문집
2024 .11
-
충격시험을 이용한 해양플랜트용 AISI 4130 이종접합 용접부의 기계적 특성 분석
한국정밀공학회 학술발표대회 논문집
2017 .12
-
AISI D2 공구강의 수중 레이저 표면 경화 처리 공정
대한기계학회 춘추학술대회
2015 .04
-
Nonlinear finite element modeling of steel-sheathed cold-formed steel shear walls
Steel and Composite Structures, An International Journal
2016 .01
이 논문의 저자 정보
최근 본 자료
댓글(0)
0