지원사업
학술연구/단체지원/교육 등 연구자 활동을 지속하도록 DBpia가 지원하고 있어요.
커뮤니티
연구자들이 자신의 연구와 전문성을 널리 알리고, 새로운 협력의 기회를 만들 수 있는 네트워킹 공간이에요.
논문 기본 정보
- 자료유형
- 학술저널
- 저자정보
- 발행연도
- 2013.12
- 수록면
- 159 - 166 (8page)
이용수
초록· 키워드
오류제보하기
In order to develop the optimum shape of an MQL carbide end-mill suitable for high speed machining of wing ribs which are a detailed part of larger wing structures, using a new material Al-Li alloy, a new MQL carbide end-mill is created that has various quantities of holes, hole sizes, and hole locations. A theoretical machining graph is generated using the hammer test and FRF simulation, and a machining test is performed in order to verify the machining stability in the high speed machining area. The optimum configuration of the MQL carbide end-mill is also presented through comparing the chattering, machining noise and cutting conditions, including the maximum cutting depth, rpm, and feed rate per teeth, for each cutter.
목차
ABSTRACT
1. 서론
2. 이론적 배경
3. 실험장치 및 방법
4. 실험결과 및 고찰
5. 결론
REFERENCES
참고문헌 (8)
참고문헌 신청
3. [학술대회논문] - S. H. Park / 2006 / A Study on the Improvement of Surface Roughness and Analysis of Cutting Force in MQL End-milling / Proc. of KSPE Fall Conference : 395 ~ 396
4. [학술지(정기간행물)] - M. Rahman / 2002 / Experimental evaluation on the effect of minimal quantities of lubricant in milling / International Journal of Machine Tools & Manufacture 42 : 539 ~ 547
5. [학술지(정기간행물)] - Anselmo Eduardo Diniz / 2002 / Cutting conditions for finish turing process aiming: the use of dry cutting / International Journal of Machine Tools & Manufacture 42 : 899 ~ 904
6. [학술지(정기간행물)] - M. Y. Yan / 1988 / Optimization of Cutting Tool for High Speed Machining / The Korean Society of Mechanical Engineering 12 (6) : 1290 ~ 1295
7. [학술지(정기간행물)] - T. L. Schmitz / 2001 / Improving High-speed Machining Material Removal Rates by Rapid Dynamic Analysis / Annals CIRP 50 (1) : 263 ~ 268
4. [학술지(정기간행물)] - M. Rahman / 2002 / Experimental evaluation on the effect of minimal quantities of lubricant in milling / International Journal of Machine Tools & Manufacture 42 : 539 ~ 547
5. [학술지(정기간행물)] - Anselmo Eduardo Diniz / 2002 / Cutting conditions for finish turing process aiming: the use of dry cutting / International Journal of Machine Tools & Manufacture 42 : 899 ~ 904
6. [학술지(정기간행물)] - M. Y. Yan / 1988 / Optimization of Cutting Tool for High Speed Machining / The Korean Society of Mechanical Engineering 12 (6) : 1290 ~ 1295
7. [학술지(정기간행물)] - T. L. Schmitz / 2001 / Improving High-speed Machining Material Removal Rates by Rapid Dynamic Analysis / Annals CIRP 50 (1) : 263 ~ 268
이 논문의 저자 정보
이 논문과 함께 이용한 논문
최근 본 자료
댓글(0)
0
UCI(KEPA) : I410-ECN-0101-2015-580-001066264