지원사업
학술연구/단체지원/교육 등 연구자 활동을 지속하도록 DBpia가 지원하고 있어요.
커뮤니티
연구자들이 자신의 연구와 전문성을 널리 알리고, 새로운 협력의 기회를 만들 수 있는 네트워킹 공간이에요.
이용수
초록· 키워드
오류제보하기
Recently, KARI(Korea Aerospace Research Institute, Korea) and CIAM(Central Institute of Aviation Motors, Russia) have made an effort in developing a centrifugal compressor for a small gas turbine engine as part of a collaboration program. This compressor has been designed as a sub-component for an axial-centrifugal compression system for a small turbo-shaft engine aiming adiabatic efficiency higher than 0.81. The geometrical design requirement imposes restrictions to have high inlet hub-to-tip ratio and inlet swirl flow.
In this study, the compressor has been designed using the generalized experimental data established from those compressors having pressure ratio of 3.7 to 5. From this generalized empirical correlation, desirable values of design parameters could be obtained. Subsequently, Quasi-3D and 3D viscous flow analyses have been performed to ensure the adopted methodology.
It is expected that the centrifugal compressor provides total pressure ratio of 4.89, corrected mass flow-rate of 1.64㎏/sec, and adiabatic efficiency of 0.815 with inlet hub-to-tip ratio of 0.641. These relatively high total pressure ratio and inlet hub-to-tip ratio are the main distinctive features in this design. Besides, one of the main features of this centrifugal compressor is the adoption of a double-row bladed diffuser to effectively decelerate the transonic flow leaving the impeller. The compressor has been manufactured and will be tested in the near future.
In this study, the compressor has been designed using the generalized experimental data established from those compressors having pressure ratio of 3.7 to 5. From this generalized empirical correlation, desirable values of design parameters could be obtained. Subsequently, Quasi-3D and 3D viscous flow analyses have been performed to ensure the adopted methodology.
It is expected that the centrifugal compressor provides total pressure ratio of 4.89, corrected mass flow-rate of 1.64㎏/sec, and adiabatic efficiency of 0.815 with inlet hub-to-tip ratio of 0.641. These relatively high total pressure ratio and inlet hub-to-tip ratio are the main distinctive features in this design. Besides, one of the main features of this centrifugal compressor is the adoption of a double-row bladed diffuser to effectively decelerate the transonic flow leaving the impeller. The compressor has been manufactured and will be tested in the near future.
목차
ABSTRACT
1. Introduction
2. Experimental Generation
3. Design of a Centrifugal Compressor for a Small Gas Turbine
4. Conclusion
References
참고문헌 (0)
참고문헌 신청함께 읽어보면 좋을 논문
논문 유사도에 따라 DBpia 가 추천하는 논문입니다. 함께 보면 좋을 연관 논문을 확인해보세요!
-
[논문] R134a용 터보냉동기의 원심압축기 개발 - Part 1 : 원심압축기 설계
한국유체기계학회 논문집
2000 .12
-
Effects of Asymmetric Tip Clearance on Centrifugal Compressor Flow
한국유체기계학회 학술대회 논문집
2005 .12
-
임펠러 특성에 따른 R134a 터보 냉동기용 원심압축기의 성능 평가
대한기계학회 춘추학술대회
2011 .04
-
효율과 무게를 고려한 원심압축기 설계에 관한 연구
대한기계학회 춘추학술대회
2013 .12
-
Hub 대 Tip 비가 큰 원심압축기에 대한 수치해석적 연구
한국항공우주학회 학술발표회 초록집
2008 .11
-
부하영역에 따른 터보냉동기용 압축기 개발
대한설비공학회 학술발표대회논문집
2011 .07
-
대체냉매용 원심압축기의 설계 및 성능시험
한국유체기계학회 학술대회 논문집
2002 .12
-
A Sensitivity Analysis of Centrifugal Compressor
KSME International Journal
2001 .09
-
Performance Prediction of Centrifugal Compressors
International Conference on Fluid Machinery
1997 .10
-
R134a용 터보냉동기의 원심압축기 설계
대한설비공학회 학술발표대회논문집
2000 .06
-
연료전지 시스템용 원심압축기 공력설계에 관한 연구
대한기계학회 춘추학술대회
2006 .11
-
Comparison of Two Methods of Flow Range Improvement in a Centrifugal Compressor
KSME/JSME THERMAL and FLUID Engineering Conference
1998 .08
-
다단 천음속 축류형 압축기 성능에 관한 실험적 연구
한국유체기계학회 논문집
2011 .12
-
Low Noise Design of Centrifugal Compressor Impeller
한국소음진동공학회 국제학술발표논문집
2003 .08
-
R134a용 1300RT급 원심압축기의 설계 및 성능시험
대한설비공학회 학술발표대회논문집
2001 .07
-
효율과 소음을 고려한 원심압축기 임펠러, 디퓨저, 볼류트의 최적설계 방법
대한기계학회 춘추학술대회
2007 .10
-
HFC-134a용 원심압축기의 성능시험 및 설계방안
설비공학논문집
2010 .03
-
원심 압축기의 성능 예측
한국자동차공학회논문집
1997 .03
-
Effects of Casing Shape on the Performance of a Small - sized Centrifugal Compressor
International Journal of Air-Conditioning and Refrigeration
2003 .09
-
원심압축기의 공력소음 저감에 관한 설계연구 Part I : 성능해석 및 소음예측
한국소음진동공학회논문집
2004 .09
이 논문의 저자 정보
최근 본 자료
댓글(0)
0
UCI(KEPA) : I410-ECN-0101-2009-554-015099958