이 연구는 대규모 절취 비탈면의 진행적 피해가 조사된 사례를 중심으로 현황 및 지반조사 등을 종합적으로 반영하여 파괴면을 추정하여 안정성을 검토하고, 이에 따른 적절한 보강대책공법을 제안하고자 한다. 연구대상 사례비탈면의 현황은 융기현상과 세굴 및 유실로 기 시공된 쏘일네일링이 대부분 파손된 것으로 조사되었다. 붕괴원인을 분석한 결과, 얕은 토사층이 무한 비탈면을 형성하고 있어 과거 석축과 암석으로 관리할 만큼 불안정한 상태에서 비탈면 절취로 힘의 불균형이 발생되면서 1차 인장균열 및 활동이 발생하였고, 집중호우로 인해 추가적으로 세굴 및 파이핑 등에 의한 대규모 유실이 발생한 것으로 분석된다. 파괴면 추정을 위하여 비탈면 배면의 붕괴지역에서 현장지표지질조사, 시추조사, 전기비저항탐사, 공내영상촬영, 공내전단시험, 지중경사계 설치 및 계측 등을 실시하였다. 시추조사 및 지표지질조사 결과 10cm전후의 두께를 갖는 토사층(붕적토+풍화토)이 무한 비탈면을 형성하고 있어 토사층 내 약대를 따라서 평면파괴가 잠재하는 것으로 나타났다. 공내영상촬영 결과 붕괴 활동면은 붕적토층 내 약대 4~6m심도에서 발달된 후 지속적인 비탈면 유실로 인해 심도 8~11m로 확대되어 진행 중인 것으로 조사되었다. 현장지표지질조사, 시추조사, 전기비저항탐사, 공내영상촬영 등의 결과를 종합적으로 반영하여 파괴면을 추정하였고, 이에 따른 안정해석 및 보강대책을 설계하였다. 따라서, 이러한 일련의 파괴면 추정에 의한 비탈면 보강 설계과정이 유사한 피해 비탈면 설계함에 유용하게 적용될 것을 기대한다.
This study is to propose a proper reinforcement countermeasure method by examining the stability by estimating the failure surface in a comprehensive way reflecting the current situation and the ground survey based on the case of the progressive damage of the large scale slope. Research subject case The present condition of the slope shows that the uplift phenomenon, Soil-Nailing which was constructed during scouring and loss was almost damage. As a result of analyzing the cause of the collapse, shallow Soil layer an infinite slope, imbalance of force on steep slope occurred in an unstable state as managed by reinforcing stone walls and rocks, primary tensile cracks and Activity occurred, it is analyzed that heavy rain caused by heavy rain and further large-scale loss due to scouring and piping occurred. In order to estimate the fracture surface, Field geological ground survey, Boring investigation, Resistivity survey, BIPS(Borehole Image capturing surface), BST(Borehole Shear Test), Underground inclinometer, etc. were carried out in the collapsed area on the rear of the slope. Excavation survey and indicators As a result of the geological survey, Soil layer(Laminated + Weathered), which has a thickness of around 10cm, formed an infinite slope, indicating that the planar fracture is latent along the camellia in Soil layer. In the activity aspect of BIPS(Borehole Image capturing surface) results, it has been developed to a depth of 4~6m in the Laminated layer and then extended to a depth of 8~11m due to continuous slope loss I understood. Site indicators Based on the results of Field geological ground survey, Boring investigation, Resistivity survey, BIPS(Borehole Image capturing surface), BST(Borehole Shear Test), Underground inclinometer, etc. destructive planes were estimated, and stability analysis and reinforcement measures were designed accordingly. Therefore, we expect that such a series of destructive plane estimation by slope reinforcement design process will be usefully applied to similar damage slope design. A thesis submitted to the Committee of the Graduate School, Kunsan National University in partial fulfillment of the requirements for degree of Master of engineering in February 2019