닭고기 패티에 소금함량을 줄이며 칼슘을 강화하기 위해 패각칼슘분말(SCP)을 첨가하며, 물성을 개선하기 위해 트랜스글루타미나아제(TG)를 첨가했을 때 나타나는 영향을 확인하기 위해 첨가하는 소금과 SCP, TG의 함량을 달리한 5개의 처리구(CON, 소금 2%; T1, 소금 0.75% + SCP 0.2%; T2, 소금 0.75% + SCP 0.2% + TG 0.2%; T3, 소금 0.5% + SCP 0.4%; T4, 소금 0.5% + SCP 0.4% + TG 0.2%)를 제조하여 패티의 육질특성 및 저장성을 비교 분석하였다. 닭고기 패티에 소금 첨가량을 낮췄을 때 회분 함량이 감소했으며 가열감량이 증가했다. 그리고 SCP와 TG를 첨가할수록 pH가 상승하였다. 소금, SCP, TG의 첨가량에 따른 육색의 변화는 없었으며, TG 없이 소금 0.5%와 SCP 0.4%를 첨가했을 때 경도와 씹음성이 감소했다. 소금을 0.5%로 줄이며 SCP 0.4%를 첨가했을 때 관능적으로 다즙성이 떨어진다는 평가를 받았지만 전체기호도를 포함한 나머지 관능평가 항목에서는 차이를 보이지 않았다. 소금의 첨가량은 닭고기 패티의 TBARS 결과에 영향을 주지 않았지만, 소금을 적게 첨가할 시 미생물 오염에 취약해질 수 있다는 결과를 보였다. 이를 통해 닭고기 패티에 소금을 줄이면서 SCP를 첨가하는 것은 관능적으로 큰 영향을 주지 않지만, 소금을 0.5%이하로 첨가 시 패티의 물성에 부정적인 영향을 줌으로 TG의 첨가를 고려해야 한다. 또한 소금 첨가량이 감소할 시 미생물로 인한 저장성에 취약해지므로 제조 시 이에 대한 추가 첨가물을 고려해야 할 것으로 판단된다.
To reduce salt content and enhance calcium in chicken patty, shell calcium powder (SCP) was added, and transglutaminase (TG) was included to improve its properties. Five different treatments were prepared to assess the effects: CON (2% salt), T1 (0.75% salt + 0.2% SCP), T2 (0.75% salt + 0.2% SCP + 0.2% TG), T3 (0.5% salt + 0.4% SCP), and T4 (0.5% salt + 0.4% SCP + 0.2% TG). Reducing salt led to decreased ash content and increased cooking loss. The addition of SCP and TG raised pH levels. Meat color remained consistent with different salt, SCP, and TG levels. However, when salt was reduced to 0.5% and SCP was added at 0.4% without TG, the patty"s hardness and chewiness decreased. Sensory evaluations showed reduced juiciness when salt was reduced to 0.5% and SCP was added at 0.4%, but no significant differences were observed in overall acceptability. Salt had no impact on TBARS results, but salt reduction to below 0.5% increased susceptibility to microbial contamination. In summary, reducing salt and adding SCP had minimal sensory impact, but when salt is reduced to 0.5% or lower, consider adding TG. Also, when decreasing salt, additional preservatives should be considered to address potential microbial contamination during manufacturing.