지원사업
학술연구/단체지원/교육 등 연구자 활동을 지속하도록 DBpia가 지원하고 있어요.
커뮤니티
연구자들이 자신의 연구와 전문성을 널리 알리고, 새로운 협력의 기회를 만들 수 있는 네트워킹 공간이에요.
논문 기본 정보
- 자료유형
- 학술저널
- 저자정보
- 발행연도
- 1986.1
- 수록면
- 3 - 12 (10page)
이용수
초록· 키워드
오류제보하기
The aim of this study is to determine the flexural properties(Modulus of Rupture, Modulus of Elasticity) of Platanus occidentalis L. laminated beams fabricated with 1, 3, 5, 8, 15 lamination and Tension, Compression lamination. The results were as follows: 1. MOR increased with increasing number of lamination in 3, 5, 8, 15-beam and Tension lamination beam. MOR of Compression lamination beam was lower than that of 3-beam, MOR of vertical beam not having Tension or compression lamination was lower than that of horizontal beam, but MOR of vertical beam with tension or compression lamination was same or slightly higher than that of horizontal beam. 2. The allowable working stress showed the same tendency. This stress increased with increasing number of lamination. This value of Tension lamination beam was higher than that of compression lamination beam. 3. MOE of all laminated beams was higher than that of solid beam and Tension lamination beam was higher than that of 3-beam. MOE of Tension lamination beam was higher than that of Compression lamination beam. MOE of all vertical beam was higher than that of horizontal beam except for T-2, T-5, C-3. 4. Most beam failures appeared to begin in tension. These tension failures were classified into Splintering tension, Cross-grained tension, Simple tension, Brittle tension. All test beam failures could be classified into three categories. 1) Tension failure 2) Compression failure 3) Horizontal shear failure.
목차
등록된 정보가 없습니다.
참고문헌 (0)
참고문헌 신청함께 읽어보면 좋을 논문
논문 유사도에 따라 DBpia 가 추천하는 논문입니다. 함께 보면 좋을 연관 논문을 확인해보세요!
-
집성재의 강도적 성질 예측에 대한 핑거 조인트와 라미나의 강도의 영향
목재공학(Journal of the Korean Wood Science and Technology)
2000 .01
-
Characteristics of Electric Motor according to the Weld-laminated Core and the Bond-laminated Core
Journal of Magnetics
2019 .12
-
식품 포장용 무용제 라미네이션 접착제의 기술 동향
포장계
2015 .01
-
오토백 인장장치의 적용성
한국토질및기초기술사회 기술발표회
2006 .01
-
Formaldehyde Emission of Wood-Based Composite Panels with Different Surface Lamination Materials Using Desiccator Method
목재공학(Journal of the Korean Wood Science and Technology)
2016 .01
-
Feasibility of Ultrasonic Log Sorting in Manufacturing Structural Lamination from Japanese Cedar Logs
목재공학(Journal of the Korean Wood Science and Technology)
2011 .01
-
The impact fracture behaviors of CFRP/EVA composites by drop-weight impact test
Carbon letters
2017 .01
-
Effect of Lamination on Complex Permeability of Mn-Zn Ferrites in a Wide Frequency Range and its Application to Improvement of HFCT
한국자기학회 학술연구발표회 논문개요집
2008 .12
-
동해 화진포 코어 퇴적물 내에 발달한 미세 엽리(lamination)에 관한 연구
대한지질학회 학술대회
2008 .10
-
UV 컷 라미네이트 필름
포장계
2005 .01
-
Ideal cell-decompositions for a hyperbolic surface and Euler characteristic
대한수학회지
2008 .01
-
태양광 모듈용 EVA의 수분 침투에 관한연구
한국진공학회 학술발표회초록집
2013 .02
-
국내 기계등급구조재의 등급구분체계 및 기준설계값 결정방법 연구
목재공학(Journal of the Korean Wood Science and Technology)
2015 .01
-
라미네이트 접착제 VOC 규제 대응
포장계
2005 .01
-
적층목질재(積層木質材)(Glulam)의 중립축(中立軸)과 강도적(强度的) 성질(性質)에 관한 연구(硏究)
목재공학(Journal of the Korean Wood Science and Technology)
1990 .01
-
A Equivalent Finite Element Model of Lamination for Design of Electromagnetic Engine Valve Actuator
Journal of Magnetics
2006 .12
-
Sliding Friction and Wear Behavior of C/C Composites Against 40 Cr Steel
Carbon letters
2009 .01
-
Quality Improvement of Oil Palm Trunk Properties by Close System Compression Method
목재공학(Journal of the Korean Wood Science and Technology)
2016 .01
-
Measurement of Dynamic MOE of 3-Ply Laminated Woods by Flexural Vibration and Comparison with Blending Strength and Creep Performances
목재공학(Journal of the Korean Wood Science and Technology)
2006 .01
이 논문의 저자 정보
최근 본 자료
댓글(0)
0