지원사업
학술연구/단체지원/교육 등 연구자 활동을 지속하도록 DBpia가 지원하고 있어요.
커뮤니티
연구자들이 자신의 연구와 전문성을 널리 알리고, 새로운 협력의 기회를 만들 수 있는 네트워킹 공간이에요.
초록· 키워드
오류제보하기
Objectives: Quantification, objectification, and standardization of lifting-thrusting manipulation are important issues in traditional Chinese medicine (TCM). The purpose of this study was to quantitatively investigate the difference in the amount of stimulation according to range and frequency among parameters of lifting-thrusting manipulation with the use of a needle insertion-measurement system.
Methods: For quantification of lifting-thrusting manipulation, an acupuncture needle insertion-measurement system was used in phantom tissue. The motor and force sensors of the needle insertion device were connected to the control software. This enabled operation of the lifting-thrusting manipulation and measurement of the acupuncture needle force. The measurement of the acupuncture needle force according to various frequencies (0.25, 0.50, 0.75, and 1 ㎐) and ranges of movement (2, 4, 6, 8, and 10 ㎜) was repeated 10 times.
Results: At a constant frequency of movement, acupuncture needle force according to range of movement (2, 4, 6, 8, and 10 ㎜) increased with increasing range of movement (p ＜ 0.05). At a constant range of movement, acupuncture needle force according to frequency of movement (0.25, 0.50, 0.75, and 1.0 ㎐) increased with increasing frequency of movement (p ＜ 0.05).
Conclusion: In this study, we conducted a quantitative comparison of the amount of stimulation according to range and frequency, the main parameters of lifting-thrusting manipulation, by using an acupuncture needle insertion-measurement system. Future studies on various manipulations and parameters are warranted to quantify and objectify the amounts of stimulation by acupuncture manipulation.
Methods: For quantification of lifting-thrusting manipulation, an acupuncture needle insertion-measurement system was used in phantom tissue. The motor and force sensors of the needle insertion device were connected to the control software. This enabled operation of the lifting-thrusting manipulation and measurement of the acupuncture needle force. The measurement of the acupuncture needle force according to various frequencies (0.25, 0.50, 0.75, and 1 ㎐) and ranges of movement (2, 4, 6, 8, and 10 ㎜) was repeated 10 times.
Results: At a constant frequency of movement, acupuncture needle force according to range of movement (2, 4, 6, 8, and 10 ㎜) increased with increasing range of movement (p ＜ 0.05). At a constant range of movement, acupuncture needle force according to frequency of movement (0.25, 0.50, 0.75, and 1.0 ㎐) increased with increasing frequency of movement (p ＜ 0.05).
Conclusion: In this study, we conducted a quantitative comparison of the amount of stimulation according to range and frequency, the main parameters of lifting-thrusting manipulation, by using an acupuncture needle insertion-measurement system. Future studies on various manipulations and parameters are warranted to quantify and objectify the amounts of stimulation by acupuncture manipulation.
목차
Introduction
Methods
Results
Discussion
References
참고문헌 (26)
참고문헌 신청
1. [학술지(정기간행물)] - Benham A / 2009 / Could acupuncture needle sensation be a predictor of analgesic response / Acupuncture in Medicine 27 (2) : 65 ~ 67
2. [학술대회논문] - Yin H / 2008 / Study of acupuncture manipulation parameter based on data mining technique / 7th Asian-Pacific Conference on Medical and Biological Engineering
3. [학술대회논문] - Tian B / 2010 / The Engineering Research and Development of Acupuncture Manipulation Instrument Based on the Motion Control / Information Processing (ISIP), 2010 Third International Symposium on
4. [단행본] - Mackereth PA / 2012 / Needling Techniques for Acupuncturists: Basic Principles and Techniques / Churchill Livingstone
5. [학술지(정기간행물)] - Liu T / 2010 / Classification and characters of physical parameters of lifting-thrusting and twirling manipulations of acupuncture / Acupuncture research 35 (1) : 61 ~
2. [학술대회논문] - Yin H / 2008 / Study of acupuncture manipulation parameter based on data mining technique / 7th Asian-Pacific Conference on Medical and Biological Engineering
3. [학술대회논문] - Tian B / 2010 / The Engineering Research and Development of Acupuncture Manipulation Instrument Based on the Motion Control / Information Processing (ISIP), 2010 Third International Symposium on
4. [단행본] - Mackereth PA / 2012 / Needling Techniques for Acupuncturists: Basic Principles and Techniques / Churchill Livingstone
5. [학술지(정기간행물)] - Liu T / 2010 / Classification and characters of physical parameters of lifting-thrusting and twirling manipulations of acupuncture / Acupuncture research 35 (1) : 61 ~
이 논문의 저자 정보
최근 본 자료
댓글(0)
0
UCI(KEPA) : I410-ECN-0101-2016-519-001075219