지원사업
학술연구/단체지원/교육 등 연구자 활동을 지속하도록 DBpia가 지원하고 있어요.
커뮤니티
연구자들이 자신의 연구와 전문성을 널리 알리고, 새로운 협력의 기회를 만들 수 있는 네트워킹 공간이에요.
이용수
초록· 키워드
오류제보하기
In machining operation, the quality of surface finish is an important factor for many turned products. In this paper, surface quality in turning machining considering angle variation has been investigated. To reach this goal, surface quality turning experiments are carried out according to cutting conditions with angle variation. The variable cutting conditions are cutting speed, feed rate and taper angle of workpiece. The surface roughness was measured and the effects of cutting conditions were analyzed by the method of analysis of variance (ANOVA). From the experimental results and ANOVA, it is found that a better surface roughness can be obtained as decreasing feed rate, increasing cutting speed. Taper angle variation has been more influenced by feed rate and cutting speed.
목차
ABSTRACT
1. 서론
2. 실험장치 및 조건
3. 실험 결과 및 고찰
4. 결론
후기
참고문헌
참고문헌 (13)
참고문헌 신청
1. [단행본] - Dornfeld, D / 2007 / Precision Manufacturing / Springer : 37 ~ 48
2. [학술지(정기간행물)] - Zhou, J. M. / 2004 / Identification of cutting errors in precision hard turing process / Journal of Materials Processing Technology 153 (154) : 746 ~ 750
3. [학술지(정기간행물)] - Topal, E. S / 2005 / A cutting force induced error elimination method for turning operations / Journal of Materials Processing Technology 170 : 192 ~ 203
4. [학술지(정기간행물)] - Abouelatta, O. B / 2001 / Surface roughness prediction based on cutting parameters and tool vibrations in turning operations / Journal of Materials Processing Technology 118 : 269 ~ 277
5. [학술지(정기간행물)] - Palanikumar, K. / 2008 / Analysis of surface roughness parameters in turning of FRP tubes by PCD tool / Journal of Materials Processing Technology 204 : 469 ~ 474
2. [학술지(정기간행물)] - Zhou, J. M. / 2004 / Identification of cutting errors in precision hard turing process / Journal of Materials Processing Technology 153 (154) : 746 ~ 750
3. [학술지(정기간행물)] - Topal, E. S / 2005 / A cutting force induced error elimination method for turning operations / Journal of Materials Processing Technology 170 : 192 ~ 203
4. [학술지(정기간행물)] - Abouelatta, O. B / 2001 / Surface roughness prediction based on cutting parameters and tool vibrations in turning operations / Journal of Materials Processing Technology 118 : 269 ~ 277
5. [학술지(정기간행물)] - Palanikumar, K. / 2008 / Analysis of surface roughness parameters in turning of FRP tubes by PCD tool / Journal of Materials Processing Technology 204 : 469 ~ 474
이 논문의 저자 정보
이 논문과 함께 이용한 논문
선삭가공에서 표면 거칠기에 미치는 냉각방법의 영향
김영덕
한국기계가공학회지
2011
.06
단침보강세라믹공구를 이용한 금형강(SKD61)의 선삭가공 시 표면거칠기에 영향을 미치는 인자 및 회귀방정식 도출
배명일
,
이이선
,
김형철
한국기계가공학회지
2012
.08
표면 거칠기를 고려한 볼베어링의 탄성유체윤활
이향
,
조용주
Tribology and Lubricants
2013
.08
금속의 표면거칠기에 대한 촉감의 마찰특성
박진확
,
김일영
,
May G
외 2명
한국트라이볼로지학회 학술대회
2012
.10
상대재료의 표면거칠기에 다른 PTFE와 UHMWPE의 마찰 및 마멸 특성
Sun Dong
,
정구현
,
이경식
Tribology and Lubricants
2011
.12
최근 본 자료
댓글(0)
0
UCI(KEPA) : I410-ECN-0101-2013-581-001374842