지원사업
학술연구/단체지원/교육 등 연구자 활동을 지속하도록 DBpia가 지원하고 있어요.
커뮤니티
연구자들이 자신의 연구와 전문성을 널리 알리고, 새로운 협력의 기회를 만들 수 있는 네트워킹 공간이에요.
논문 기본 정보
- 자료유형
- 학술저널
- 저자정보
- 발행연도
- 2011.12
- 수록면
- 830 - 836 (7page)
이용수
초록· 키워드
오류제보하기
Most of pitch/yaw reducers consist of several planetary geartrains. Planetary geartrains make gearboxes to be small and light, low noise and good efficiency. Most important thing in the planetary geartrain is load distribution on the gear tooth flank. In this study, the effect of output shaft bearings on the load distribution of gear tooth flank has been investigated. The commercial software was employed to compare the load distribution of two models depending on the bearing type. The spherical roller bearing(SRB) and the cylindrical roller bearing(CRB) were used as output shaft bearings in the 1<SUP>st</SUP> model, and two taper roller bearings(TRB) were used in the 2<SUP>nd</SUP> model. As a result, it was found that the 2<SUP>nd</SU> model. showed better performances on the load distribution of gear tooth flank, this results stated that the output shaft bearing system could be important consideration when designing reducers for wind turbine systems.
목차
Abstract
1. 서론
2. 풍력발전기용 유성 감속기의 모델
3. 풍력발전기용 유성 감속기의 해석
4. 결론
후기
참고문헌
참고문헌 (12)
참고문헌 신청
1. [학술대회논문] - Abe, T. / 2009 / Advanced CAE Methods for Automotive Drivetrain System Gear Whine Optimization / Proceedings of MPT2009-Sendai, JSME International Conference on Motion and Power Transmission : 1 ~ 15
2. [기타자료] - American Gear Manufacturers Association (AGMA) / 2006 / Design Manual for Enclosed Epicyclic Gear Drives, ANSI/AGMA 6123-B06
3. [학술대회논문] - Chong, T. H. / 2009 / An Optimum Design of Planetary Gear Considering the Volume / Proc. of KSMTE Autumn conference : 369 ~ 373
4. [기타자료] - International Organization for Standardization (ISO) / 2007 / Calculation of load capacity of spur and helical gears, ISO 6336-1
5. [학술지(정기간행물)] - Kamaya, F. / 2008 / A Rapid Method for the investigation of System-Wide Parameter Variation Effects on Epicyclic Gear Whine / Transactions of Society of Automotive Engineers of Japan 39 (6) : 647 ~ 652
2. [기타자료] - American Gear Manufacturers Association (AGMA) / 2006 / Design Manual for Enclosed Epicyclic Gear Drives, ANSI/AGMA 6123-B06
3. [학술대회논문] - Chong, T. H. / 2009 / An Optimum Design of Planetary Gear Considering the Volume / Proc. of KSMTE Autumn conference : 369 ~ 373
4. [기타자료] - International Organization for Standardization (ISO) / 2007 / Calculation of load capacity of spur and helical gears, ISO 6336-1
5. [학술지(정기간행물)] - Kamaya, F. / 2008 / A Rapid Method for the investigation of System-Wide Parameter Variation Effects on Epicyclic Gear Whine / Transactions of Society of Automotive Engineers of Japan 39 (6) : 647 ~ 652
이 논문의 저자 정보
이 논문과 함께 이용한 논문
Study on the Tooth Micro-Geometry Optimization of Planetary Gear for Drive Reducer
노승윤
,
김래성
,
조성현
외 1명
Journal of the Korean Society for Precision Engineering
2017
.06
날개 길이 및 후면부 절개 비율에 따른 해상용 수직축 풍력발전기 특성 평가
김남훈
,
김경수
,
윤양일
외 1명
한국신·재생에너지학회 학술대회 초록집
2011
.05
해상풍력발전기 Pitch Drive 감속기 하중분포에 관한 연구
이인범
,
류성기
한국기계가공학회 춘추계학술대회 논문집
2013
.11
플라스틱 하모닉 감속기의 구조 및 동 응력 해석
박인규
,
김기환
,
임영남
한국정밀공학회 학술발표대회 논문집
2013
.05
풍력발전기의 경년화를 고려한 자동튜닝 알고리즘 개발
김세윤
,
김성호
한국지능시스템학회 논문지
2012
.04
최근 본 자료
댓글(0)
0
UCI(KEPA) : I410-ECN-0101-2013-552-001324461