지원사업
학술연구/단체지원/교육 등 연구자 활동을 지속하도록 DBpia가 지원하고 있어요.
커뮤니티
연구자들이 자신의 연구와 전문성을 널리 알리고, 새로운 협력의 기회를 만들 수 있는 네트워킹 공간이에요.
논문 기본 정보
- 자료유형
- 학술저널
- 저자정보
- 발행연도
- 2011.9
- 수록면
- 281 - 287 (7page)
이용수
이 논문의 연구 히스토리 (6)
2011
Minimization of Cogging Force in a Stationary Discontinuous Armature Linear Permanent Magnet Motor at the Outlet Edge
Yong-Jae Kim
,
Sang-Yong Jung
Journal of Magnetics
2011.09
학술저널
A Study on the Reduction of Cogging Force of Stationary Discontinuous Armature Linear Synchronous Motor Using Auxiliary Teeth
Yong-Jae Kim
,
Kyu Myung Lee
,
Masaya Watada
Journal of Magnetics
2011.09
학술저널
2008
Reduction of the Cogging Force at a Moving-Coil-Type Slotless Linear Synchronous Motor
Yong-Jae Kim
,
Youn-Ok Choi
,
Masaya Watada
한국자기학회 학술연구발표회 논문개요집
2008.12
학술대회자료
Cogging Force Reduction of a Stationary Discontinuous Armature PM-LSM by Magnet Segmentation
Yong-Jae Kim
,
Youn-Ok Choi
,
Geum-Bae Cho
한국자기학회 학술연구발표회 논문개요집
2008.12
학술대회자료
- 이 논문의 후속연구가 궁금하신가요?
- 연관 학술논문 또는 학술발표를 통해 보다 발전된 연구결과를 확인하실 수 있습니다.
- 이 논문의 연구 히스토리 확인하기
초록· 키워드
오류제보하기
The stationary discontinuous armatures that are used in permanent magnet linear synchronous motors (PMLSMs) have been proposed as a driving source for transportation systems. However, the stationary discontinuous armature PM-LSM contains the outlet edges which always exist as a result of the discontinuous arrangement of the armature. For this reason, the high alteration of the outlet edge cogging force produced between the armature’s core and the mover’s permanent magnet when a mover passes the boundary between the armature’s installation part and non-installation part has been indicated as a problem. Therefore, we have examined the outlet edge cogging force by installing the auxiliary teeth at the armature’s outlet edge in order to minimize the outlet edge cogging force generated when the armature is arranged discontinuously. Moreover, we obtained the calculation by analyzing the shape of the auxiliary teeth in which the outlet edge cogging force is minimized the most.
목차
1. Introduction
2. Force Generated at the Outlet Edge
3. 2-D Numerical Analysis of the Outlet Edge Cogging Force
4. Conclusion
Acknowledgements
References
참고문헌 (5)
참고문헌 신청
R. Akmese / 1992 / IEEE Trans. Magn 28:3042
M. Sanada / 1997 / IEEE Trans. Industry Appl 33:966
장정환 / 2010 / Transverse Flux Linear Machine with High Thrust for Direct Drive Applications / Journal of Magnetics 15(2):64~69
김용재 / 2009 / Cogging Force Verification of the Back-yoke Length of a Moving-coil-type Slotless Linear Synchronous Motor / Journal of Magnetics 14(1):47~51
Y. Kim / 2006 / IET Electric Power Appl 153:585
M. Sanada / 1997 / IEEE Trans. Industry Appl 33:966
장정환 / 2010 / Transverse Flux Linear Machine with High Thrust for Direct Drive Applications / Journal of Magnetics 15(2):64~69
김용재 / 2009 / Cogging Force Verification of the Back-yoke Length of a Moving-coil-type Slotless Linear Synchronous Motor / Journal of Magnetics 14(1):47~51
Y. Kim / 2006 / IET Electric Power Appl 153:585
이 논문의 저자 정보
최근 본 자료
댓글(0)
0
UCI(KEPA) : I410-ECN-0101-2013-428-000709312