메뉴 건너뛰기
.. 내서재 .. 알림
소속 기관/학교 인증
인증하면 논문, 학술자료 등을  무료로 열람할 수 있어요.
한국대학교, 누리자동차, 시립도서관 등 나의 기관을 확인해보세요
(국내 대학 90% 이상 구독 중)
로그인 회원가입 고객센터 ENG
주제분류
인문학
인문학 일반 역사학 철학 종교학 어문학 기타 인문학
사회과학
사회과학 일반 경영학 관광학 교육학 군사학 문헌정보학 법학 사회학 신문방송학 심리과학 정치외교학 지리학 행정학 경제학 무역학 인류학 기타 사회과학
자연과학
자연과학 일반 물리학 생물학 생활과학 수학·통계학 천문학 지구과학 화학 기타 자연과학
공학
공학 일반 건축공학 기계공학 산업공학 재료·에너지공학 전기전자공학 조선해양공학 화학공학 컴퓨터학 기타공학
의약학
의학 일반 간호학 수의학 약학 한의학 기초의학 임상의학 기타 의약학
농수해양학
농수해양학 일반 농학 수산학 식품과학 임학 축산학 해상운송학 기타 농수해양학
예술체육학
예술 일반 디자인 미술 미용 사진 음악학 의상 체육 공연매체예술 기타 예술체육학
복합학
학제간연구 과학기술학 뇌인지과학 기술정책 기타 복합학

ENG

추천
검색
질문

논문 기본 정보

자료유형
학술저널
저자정보
저널정보
대한기계학회 Journal of Mechanical Science and Technology KSME International Journal Vol.18 No.5
발행연도
2004.5
수록면
770 - 779 (10page)

이용수

표지
📌
연구주제
📖
연구배경
🔬
연구방법
🏆
연구결과
AI에게 요청하기
추천
검색
질문

초록· 키워드

오류제보하기
This paper describes the micro cutting of wear resistant tungsten carbides using PCD (Poly-Crystalline Diamond) cutting tools in performance with SEM (Scanning Electron Microscope) direct observation method. Turning experiments were also carried out on this alloy (V50) using a PCD cutting tool. One ot the purposes of this study is to describe clearly the cutting mechanism of tungsten carbides and the behavior of WC particles in the deformation zone in orthogonal micro cutting. Other purposes are to achieve a s;ystematic understanding of machining characteristics and the effects of machning parameters on cutting force, machined surface and tool wear rates by the outer turning of this alloy carried out using the PCD cutting tool during these various cutting conditions. A sumary of the results are as follows: (1)From the SEM direct observation in cutting the tungsten carbide,WC particles are broken and come into contact with the tool dege directly. This causes tool wear in which portions scrape the tool in a strong manner. (2)There are two chip formation types. One is where the shear angle is comparatively small and the crack of the shear plane becomes wide. The other is a type where the shear angle is above 45 degrees and the crack of the shear plane does not widen. These differences are caused by the stress condition which gives rise to the friction at the shear plane.(3) The thrust cutting forces tend to increase more rapidly than the principal forces, as the depth of cut and the cutting speed are increased preferably in the orthogonal micro cutting. (4) The tool wear on the flank face was larger than that on the rake face in the orthogonal micro cutting. (5)Three components of cutting force in the conventional turning experiments were different in balance from ordinary cutting such as the cutting of steel or cast iron. Those expressed a large value of thrust force, principal force, and feed force. (6)From the viewpoint of high efficient cutting found within this research, a proper cutting speed was 15 m/min and a proper feed rate was 0.1 mm/rev. In this case, it was found that the tool life of a PCD tool was limited to a distance of approximately 230m. (7) When the depth of cut was 0.1 mm, there was no influence of the feed rate on the feed force. The feed force tended to decrease, as the cutting distance was long, because the tool was worn and the tool dege retreated. (8)The main tool wear of a PCD tool in this research was due to the flank wear within the maximum value of Vmax being about 260μm.

목차

Abstract

1.Introduction

2.Experimental Work

3.Result and Discussion

4.Conclusion

References

참고문헌 (10)

참고문헌 신청
[학술지(정기간행물)] - / 1993. / A Study on the High Efficiency Grinding of WC-Co 17 (3) : 721 ~ 730 google schola [학술지(정기간행물)] - / 1993. / A Study on the Grinding of WC-Co with High Quality google schola [학술지(정기간행물)] - / 1997 / Japan Society for the Promotion of Machine Industry : 95 ~ 0321 google schola [학술지(정기간행물)] - / 1997 / Japan Society for the Promotion of Machine Industry : 95 ~ 0323 google schola [학술지(정기간행물)] - / 1997 / Japan Society for the Promotion of Machine Industry : 95 ~ 0325 google schola

함께 읽어보면 좋을 논문

논문 유사도에 따라 DBpia 가 추천하는 논문입니다. 함께 보면 좋을 연관 논문을 확인해보세요!

이 논문의 저자 정보

이 논문과 함께 이용한 논문

Effect of Reduced Graphite Oxide as Substrate for Zinc Oxide to Hydrogen Sulfide Adsorption
Nu Ri Jeon ,  Hoon Sub Song ,  Moon Gyu Pa 외 4명 청정기술 2013 .09
탄소 피복된 SnO₂-SiO₂ 음극활물질의 전기화학적 특성
정구현 ,  나병기 청정기술 2013 .03
FE-SEM을 이용한 커튼 코팅 도공층의 공극 구조 연구 및 블레이드 코팅 방식과의 비교 : 안료조성변화에 의한 영향을 중심으로
김채훈 ,  이학래 ,  윤혜정 한국펄프·종이공학회 학술발표논문집 2011 .04
Investigations on the Development of Powder Concrete with Nano-SiO₂ Particles
Byung Wan Jo ,  Chang Hyun Kim ,  Jae Hoon Lim KSCE JOURNAL OF CIVIL ENGINEERING 2007 .01

최근 본 자료

전체보기

댓글(0)

0

UCI(KEPA) : I410-ECN-0101-2009-550-014053027